Maintains Competent Climber/Rescuer Certification - Competent Climber training must meet or exceed applicable sections in OSHA Standard 29 CFR 1910 and 29 CFR 1926. It must also meet or exceed applicable sections of ANSI/ASSE A10.48, ANSI Z359 and the NATE Tower Climber Fall Protection Training Standard (CTS). Written testing and continuous, critical observation by a competent person while in-training are required. Maintains Radio Frequency (RF) Certification – This annual training must meet or exceed the requirements of all current Federal Communications Commission-Office of Engineering and Technology (FCC OET) Bulletins with regards to Human Exposure levels. Maintains First Aid/Cardio Pulmonary Resuscitation/Blood Borne Pathogens (FA/CPR/BBP) Certification – Must be properly trained and able to render First Aid, Cardio Pulmonary Resuscitation and protect against infection from Blood Borne Pathogens. Such training must be in accordance with OSHA 29 CFR 1926.50 and result in a valid certificate from the U.S Bureau of Mines, the American Red Cross or equivalent. Hand Signaling – Must demonstrate competency in the hand signals defined as part of 29 CFR 1926.1419 Climbing Facilities – Must be able to address issues concerning climbing facilities (rung/rail, step bolts, integral climbing face, etc.) including the safety climb, with the structure owner, and such issues must be addressed IAW ANSI/TIA 222, manufacturer specifications, and Engineer of Record (EOR) requirements. Electrical Safety - Must be trained in the identification and abatement of electrical hazards that may be encountered as a part of the SOW. Such training will address the proper use of monitors, lock out tag out, system turn down and client communication IAW 29 CFR 1926.4, Subpart K. Compliance (CPL) 02-01-056 – Must have an awareness of the requirements set forth in Inspection Procedures for Accessing Communications Structures by Hoist. Call Before You Dig – Must assist the MCF to ensure all utilities are located and marked prior to digging/excavation per 29 CFR 1926.651(b) (2).

1. Maintains Competent Climber/Rescuer Certification
2. Maintains RF Certification
3. Maintains FA/CPR/BBP Certification
4. Hand Signaling
5. Climbing Facilities
6. Electrical Safety
7. CPL 02-01-056
8. Call Before You Dig

Obtains the following endorsements: For work involving Guyed Structures Guy Wire System 1 required Guy Wire System 2 may be required based on SOW Assists Maintenance and Condition Foreman (MCF) in the following: Creation of Job Hazard Assessment (JHA) per ANSI/ASSE A10.48, Section 4. Creation of the Fall Protection Plan per ANSI/ASSE A10.48, Section 6 Creation of Rescue Plan per ANSI/ASSE A10.48, Section 6.15 Understands and applies the following: Applies client/structure owner procedural requirements for site access and SOW – competent in the review and understanding of the employer/client/structure owner’s Notice to Proceed (NTP) documentation and notification requirements which are SOW dependent. Any conflicts between the design for maintenance and condition assessment requirements of ANSI/TIA 222, ANSI/TIA 322 and ANSI/ASSE A10.48 the ANSI/TIA 222 shall prevail. ANSI/TIA 222 – Demonstrate understanding of the applicable sections of TIA 222, Structural Standard for Antenna Supporting Structures and Antennas. This standard is the recognized consensus standard and has been adopted by the International Building Code (IBC) to establish the design, maintenance and condition assessment requirements of antenna supporting structures and shall be used along with the structure owner’s established maintenance and condition assessment program. Specifically related to the SOW:  Section 9 - Foundations and Anchorages  Section 10 – Protective Grounding  Section 11 – Obstruction and Marking  Section 12 – Climbing Facilities  Section 13 – Plans, Assembly Tolerances and Markings  Section 14 – Maintenance and Condition Assessment  Annex G – Geotechnical Investigation  Annex H – Additional Corrosion Control  Annex I – Climber Attachment Anchorages  Annex J – Maintenance Condition Assessment  Annex K – Measuring Guy Tensions ANSI/TIA 322 – Demonstrate understanding of applicable sections of TIA 322, Standard for Loading, Analysis and Design Criteria Related to the Installation, Alteration and Maintenance of Communication Structures, specifically Section 2 – Structural Considerations During Construction, relative to the SOW. ANSI/ASSE A10.48 – Demonstrate understanding of and comply with requirements of ANSI/ASSE A10.48, Criteria for Safety Practices with the Construction, Demolition, Modification and Maintenance of Communication Structures. The ANSI/ASSE A10.48 is to be utilized for planning the means and methods to conduct a maintenance and condition assessment governed by the requirements of ANSI/TIA 222 and/or owner’s representative. The ANSI/ASSE A10.48 establishes the minimum criteria for safe work practices and training for personnel performing work on communication structures. Must be able to comply with all sections and appendices relative to the SOW. American Institute Steel Construction (AISC) Manual of Steel Construction and Research Council on Structural Connections (RCSC) Specification for Structural Joints Using High-Strength Bolts – Must understand and apply proper installation and tightening of bolts, “turn of nut” or the EOR prescribed method. Proficient in Client Based Deliverables – Must be able to gather the required information which may include photographs, red line information, installation information, testing data, and any other required documentation specific to the SOW.

1. Obtains the following endorsements: For work involving Guyed Structures - Guy Wire System 1 required
2. Obtains the following endorsements: For work involving Guyed Structures - Guy Wire System 2 may be required based on SOW
3. Assists CMF in the following: Creation of Job Hazard Assessment (JHA)
4. Assists CMF in the following: Creation of Rescue Plan
5. Assists CMF in the following: Creation of Fall Protection Plan
6. Understands and applies the following: Procedural requirements for site access and SOW
7. Understands and applies the following: ANSI/TIA 222
8. Understands and applies the following: ANSI/TIA 322
9. Understands and applies the following: ANSI/ASSE A10.48
10. Understands and applies the following: AISC(RCSC) Manual of Steel Construction
11. Proficient in Client Based Deliverables

SOW Required Tools – Must be able to demonstrate competency with any tool required by the SOW. This will include understanding the manufacturer’s documentation and proper application of the tool in a safe manner. Will have the authority to tag out tools and equipment. A critical part of this training includes the responsibility to request training when required to utilize a tool that they have not previously been trained to use. Refer to CFR 1926, Subpart I, CFR 1910, Subpart P and tool manufacturer’s instructions.

1. SOW Required Tools

Federal Motor Carrier Safety Regulations (FMCSR) – Must have a basic understanding of Federal Motor Carrier Safety Regulations as they apply to company service vehicles, even in the event that they are not a driver. The intent is to support the drivers in compliance. Load Securement – Must be competent in the securement of loads IAW 49 CFR 390.5. SOW Required Equipment – Must be able to demonstrate competency with any equipment required by the SOW. This must include understanding the manufacturer’s documentation and proper application of the equipment in a safe manner. Will have the authority to tag out defective equipment. A critical part of this training includes the responsibility to request training when required to utilize any equipment that they have not previously been trained to use.

1. FMCSR
2. Load Securement
3. SOW Required Equipment

Awareness training does not imply the person has the skills to perform work. To perform the work listed below the individual should have the corresponding endorsement and/or training. Assists Maintenance and Condition Assessment Foreman (MCF) in the following – Creation of Job Hazard Assessment (JHA) per ANSI/ASSE A10.48, Section 4. Creation of the Fall Protection Plan per ANSI/ASSE A10.48, Section 6 Creation of Rescue Plan per ANSI/ASSE A10.48, Section 6.15 Creation of Class Specific Rigging/Lift Plan per ANSI/ASSE A10.48, Section 13.3 Guy Wire Systems - Overview of the basic components such as the anchor shafts, turnbuckles, thimbles, end terminations, shackles, end sleeves, guy wires, grounding, cathodic protection, etc. The plumb, twist and tension shall be discussed IAW ANSI/TIA 222 annex K and ANSI/TIA 322. Structural Modification – Awareness must include the ability to evaluate a structural modification SOW, its impact to rigging classification, climbing facilities, mounting locations, and must communicate if there is any deviation IAW most current published revision of ANSI/TIA 222. Must understand the condition assessment process prior to accessing the structure. Unmanned Aerial System (UAS) – Include that this technology is continually developing and its ability to support our infrastructures. Personal UAS are never to be used on site. The use of these systems is governed by the FAA 14 CFR Part 107. Shall adhere to additional state regulations, permits, insurance and site owner requirements. Tower Service Elevator – Most commonly found in Broadcast Structures. Must be able to recognize and understand the hazards, operation and inspection requirements.

1. Class Specific Rigging/Lift Plan per ANSI/TIA 322, and ANSI/ASSE A10.48
2. Competent Rigger
3. Structural Modification(s)
4. Unmanned Aerial System (UAS)
5. Tower Service Elevator

Competent Climber training must meet or exceed applicable sections in OSHA Standard 29 CFR 1910 and 29 CFR 1926. It must also meet or exceed applicable sections of ANSI/ASSE A10.48, ANSI Z359 and the NATE Tower Climber Fall Protection Training Standard (CTS). Written testing and continuous, critical observation by a competent person while in-training are required. *Once a person has achieved this level of credentialing they only need to maintain the awareness portion of this training in the event this will be a skill utilized by them in their activities.

This annual training must meet or exceed the requirements of all current Federal Communications Commission-Office of Engineering and Technology (FCC OET) Bulletins with regards to Human Exposure levels.

Must be properly trained and able to render First Aid, Cardio Pulmonary Resuscitation and protect against infection from Blood Borne Pathogens. Such training must be in accordance with OSHA 29 CFR 1926.50 and result in a valid certificate from the U.S Bureau of Mines, the American Red Cross or equivalent.

Teaches student hand signaling and student must demonstrate competency in the hand signals defined as part of 29 CFR 1926.1419

Must be able to address issues concerning climbing facilities (rung/rail, step bolts, integral climbing face, etc.) including the safety climb, with the structure owner, and such issues must be addressed IAW ANSI/TIA 222, manufacturer specifications, and Engineer of Record (EOR) requirements.

Must be trained in the identification and abatement of electrical hazards that may be encountered as a part of the SOW. Such training will address the proper use of monitors, lock out tag out, system turn down and client communication IAW 29 CFR 1926.4, Subpart K.

Must have an awareness of the requirements set forth in Inspection Procedures for Accessing Communications Structures by Hoist.

Must assist the MCF to ensure all utilities are located and marked prior to digging/excavation per 29 CFR 1926.651(b) (2).

Demonstrate understanding of the applicable sections of TIA 222, Structural Standard for Antenna Supporting Structures and Antennas. This standard is the recognized consensus standard and has been adopted by the International Building Code (IBC) to establish the design, maintenance and condition assessment requirements of antenna supporting structures and shall be used along with the structure owner’s established maintenance and condition assessment program. Specifically related to the SOW: Section 9 - Foundations and Anchorages Section 10 – Protective Grounding Section 11 – Obstruction and Marking Section 12 – Climbing Facilities Section 13 – Plans, Assembly Tolerances and Markings Section 14 – Maintenance and Condition Assessment Annex G – Geotechnical Investigation Annex H – Additional Corrosion Control Annex I – Climber Attachment Anchorages Annex J – Maintenance Condition Assessment Annex K – Measuring Guy Tensions

Demonstrate understanding of applicable sections of TIA 322, Standard for Loading, Analysis and Design Criteria Related to the Installation, Alteration and Maintenance of Communication Structures, specifically Section 2 – Structural Considerations During Construction, relative to the SOW.

Demonstrate understanding of and comply with requirements of ANSI/ASSE A10.48, Criteria for Safety Practices with the Construction, Demolition, Modification and Maintenance of Communication Structures. The ANSI/ASSE A10.48 is to be utilized for planning the means and methods to conduct a maintenance and condition assessment governed by the requirements of ANSI/TIA 222 and/or owner’s representative. The ANSI/ASSE A10.48 establishes the minimum criteria for safe work practices and training for personnel performing work on communication structures. Must be able to comply with all sections and appendices relative to the SOW.

Must understand and apply proper installation and tightening of bolts, “turn of nut” or the EOR prescribed method.

Must be able to demonstrate competency with any tool required by the SOW. This will include understanding the manufacturer’s documentation and proper application of the tool in a safe manner. Will have the authority to tag out tools and equipment. A critical part of this training includes the responsibility to request training when required to utilize a tool that they have not previously been trained to use. Refer to CFR 1926, Subpart I, CFR 1910, Subpart P and tool manufacturer’s instructions.

Must have a basic understanding of Federal Motor Carrier Safety Regulations as they apply to company service vehicles, even in the event that they are not a driver. The intent is to support the drivers in compliance.

Must be competent in the securement of loads IAW 49 CFR 390.5.

Must be able to demonstrate competency with any equipment required by the SOW. This must include understanding the manufacturer’s documentation and proper application of the equipment in a safe manner. Will have the authority to tag out defective equipment. A critical part of this training includes the responsibility to request training when required to utilize any equipment that they have not previously been trained to use.

Awareness training does not imply the person has the skills to perform work. To perform the work listed below the individual should have the corresponding endorsement and/or training. Assists Maintenance and Condition Assessment Foreman (MCF) in the following – o Creation of Job Hazard Assessment (JHA) per ANSI/ASSE A10.48, Section 4. o Creation of the Fall Protection Plan per ANSI/ASSE A10.48, Section 6 o Creation of Rescue Plan per ANSI/ASSE A10.48, Section 6.15 o Creation of Class Specific Rigging/Lift Plan per ANSI/ASSE A10.48, Section 13.3 Guy Wire Systems - Overview of the basic components such as the anchor shafts, turnbuckles, thimbles, end terminations, shackles, end sleeves, guy wires, grounding, cathodic protection, etc. The plumb, twist and tension shall be discussed IAW ANSI/TIA 222 annex K and ANSI/TIA 322. Structural Modification – Awareness must include the ability to evaluate a structural modification SOW, its impact to rigging classification, climbing facilities, mounting locations, and must communicate if there is any deviation IAW most current published revision of ANSI/TIA 222. Must understand the condition assessment process prior to accessing the structure. Unmanned Aerial System (UAS) – Include that this technology is continually developing and its ability to support our infrastructures. Personal UAS are never to be used on site. The use of these systems is governed by the FAA 14 CFR Part 107. Shall adhere to additional state regulations, permits, insurance and site owner requirements. Tower Service Elevator – Most commonly found in Broadcast Structures. Must be able to recognize and understand the hazards, operation and inspection requirements.